View GEI-100335_341433.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

GE Motors & Industrial Systems
- Cmm'sR
*^ ,.r
_
Encoder Signal Repeater-
GEL100335
These instructions do not purport to cover all details or variations in equipment, nor to provide every possible contingency to be metduring installation, operation, and maintenance. If further information is desired or if particular problems arise that are not covered sufficiently for the purchaser's purpose, the matter should be referred to GE Motors & Industrial Systems.This document contains proprietary information of General Electric Company, USA and is furnished to its customer solely to assist that customer in the installation, testing, operation, and/or maintenance of the equipment described. This document shall not be reproduced in whole or in part nor shall its contents be disclosed to any third party without the written approval of GE Motors & Industrial Systems.
0 1997 by General Electric Company, USA. All rights reserved.
--
--I------
The 6KAV3OOESR Encoder Signal Repeater Card is designed to transmit an encoder signal to a remote user connected to the AV-300 drive. The output signals are electrically isolated. The card has to be installed on the regulation card of the AV-300 drive, in place of "option B" card assembly on the left-hand side of the regulation card.
_".
.-.
,,A
`
c
1 XE 16
r
"""""""'
I
Dimensions:
4 x 2.2 inches (102 x 56 mm)
Weight : 0.22 pounds (100 g)
Through XRE connector the Encoder Signal Repeater card detects encoder signals from the drive regulator. Through XBB connector it receives voltage input (+5V) for its synchronization circuit. XE connector is used to provide the TTL or HTL signals encoder output and to receive an external voltage supply of either +5V or +15 to +24V. Configuration of SW0 and SW1 Jumper determines external power requirement and output signal levels. Table 1: Jumpers SW0 and SW1
Switches configuration
SW0 and SW1 in position A PWR supply +5v
Available output
SW0 and SW 1 in position B
+l5...+24V
TTL logic HTL and TTL logic
P-0163
Two electric~~u~pu~p_rotocols__ available, asshown ,above,~~,~,~~~~~~~t~~~, is not,grotected against short are _.I .r^.,--,u., , . .<.*a I. .I .~.__, I circuit. The synchronism assures that the channel C pulse (zero pulse) is in phase with and has the same duration as one channel B pulse. In case of noise on the encoder signals, connect ground GND with terminal 11 of the regulation card through a capacitor ( 0.47 PF 850V ).
1
GEI-100335
Drive Regulator
Card
External supply
I
i i
TA+ 4+ TA4TBv.
TB+ 3+
XEI XE9
PWR Corm. XRE
XE4
XE8
XE15
ET4 XE6 XE13
Encoder Signal Repeater
D-sub miniature connector of 15 sockets, assembly on the card. To join tie input conductors and output signals use a male connector in accordance with DIN 41 652. Table 2: Assignment of the Plug Connector XE
Table 3: Recommended Cable cross-section area and length for connection Section [mm ] max Length feet [m] 0.22 180 [55] 0.5 140 11251 0.75 500 [150]
P-0165
Table 4: LEDs on the card Designation +5 v PWR RDY I , Color green green red Function ON when there is power present ON when there is external supply ON when external supply is not OK -9
_ wJ166 _
3
GEL100335
Notes
,
_
_
1
_
-_,
..".-....i
_
_..
.-
,
`
,
,
4
E
:.,.
,_
.
.
'
),`,
I I @
P
We bring good things to life.
GEI-100335 Rev. 1.0 (297)
GE Motors & Industrial
Internet
Systems
Address: http://www.ge.com

▲Up To Search▲

Price & Availability of GEI-100335

	To Download GEI-100335 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .